It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
First, you need to gather the equipment needed. This will include a shovel or post hole digger, a driving tool, hammer or mallet, and the proper type of rod. They are eight feet long and usually made of copper. Ask your hardware store to point you to the right type of rods for the job. Using the wrong material will not protect your home from a surge.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
After you reach as far as you can go, add some water to the hole. You don't have to fill the hole, just make it moist so you can begin pushing the rod in by hand. The water will help with this process. As you go deeper with the pole, add more water to help out. You can move the pole back and forth with the pointed end in the ground to make it easier. Once you reach the point it won't go deeper by hand, grab another tool.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Fill in the hole and finish the job. Some areas require the rod to be completely underground and others don't have a rule. It is best to keep it low enough that the lawn mower won't hit it. If it is in an area that will be mowed, it is a good idea to bury the connecting wire as well as the rod completely under the ground.
First, you need to gather the equipment needed. This will include a shovel or post hole digger, a driving tool, hammer or mallet, and the proper type of rod. They are eight feet long and usually made of copper. Ask your hardware store to point you to the right type of rods for the job. Using the wrong material will not protect your home from a surge.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Once you have the spot selected, begin digging with the post hole digger. If you do not have one, a shovel will do the job just fine. You do not need to dig a wide hole, just as deep as you can.
After you reach as far as you can go, add some water to the hole. You don't have to fill the hole, just make it moist so you can begin pushing the rod in by hand. The water will help with this process. As you go deeper with the pole, add more water to help out. You can move the pole back and forth with the pointed end in the ground to make it easier. Once you reach the point it won't go deeper by hand, grab another tool.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Fill in the hole and finish the job. Some areas require the rod to be completely underground and others don't have a rule. It is best to keep it low enough that the lawn mower won't hit it. If it is in an area that will be mowed, it is a good idea to bury the connecting wire as well as the rod completely under the ground.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
Out Of Topic Show Konversi KodeHide Konversi Kode Show EmoticonHide Emoticon